The post Short 45-Female/Male-PA094 appeared first on Aqua-Air Wet/Dry.

1– AA124 Auto Detail Cleaning Station

6– PA091 Long Sweep 90-Female/Female

2– PA092 Long Sweep 90-Female/Male

3– PA093 Short 45-Female/Female

1– PA094 Short 45-Female/Male

1– PA096 Wye 45 Degree-F/F/F

6– PA097 2′ Coupling-PVC 20

8– PA135 Pipe Strap 2′ Aqua Air

2– BR138 Nipple 1/2′ X 1/4′  Hex Brass

24– PA180 Wire Tie 11′ White

45 FT– PA178 Wire Brown 18 Guage 2 Conduct.

1– BR502 Coupler 3/8′ Barb PEX

12– BR503 Crimp Band 3/8′ PEX

4– BR501 Tee Barb 3/8-3/8-3/8 PEX

4–  BR506 Swivel Adapt 1/2-1/3 Barb PEX

The post Auto Detail Station/ Installation Kit-AA516 appeared first on Aqua-Air Wet/Dry.

• Helps exhaust fine dust into the open air outside the house, maintaining a healthier internal environment

Part Number:PA304

The post Exhaust Cover-PA304 appeared first on Aqua-Air Wet/Dry.

• Provides proper protection to the piping system while construction is going on
• Extra Tab – easy to remove for valve installation
• Screws required

The post Plaster Gaurd-PA140 appeared first on Aqua-Air Wet/Dry.

VAC-VALVE AIR RELIEF SYSTEM

Purpose: The Vac-Valve is designed to protect your central vacuum system from damage caused by blockage.

The Vac-Valve comes fully assembled and ready for use. However, it is important to install the Vac-Valve properly in order to receive the full protection it was designed to provide.

Installation Instructions:

1)  The Vac-Valve should be installed into a sweep 90 tee connection prior to where the pipe enters the central vacuum unit. The valve can sit either horizontally or vertically, as position does not affect its operation. Please ensure the Vac-Valve is mounted securely regardless of its position.

2) The Vac-Valve must be set for the size of the motor in order for it to provide the proper protection. To set the Vac-Valve, tighten the adjuster nut to compress the spring to the point where the valve will not open when the air flow is cut off 100%.

3) Once you reach the point where the Vac-valve will not open, turn the adjuster nut back 1 complete turn (360 degrees). This setting will usually allow the Vac-Valve to open and provide cooling air into the system if a blockage occurs. Sometimes a turn of 360 degrees may not be sufficient to open the Vac-Valve & allow cooling air to enter – so make minor adjustments moving the nut up & down until you reach the point where the Vac-Valve opens when the air flow is cut off 100%.

4) The Vac-Valve should remain closed if the central vacuum is operating normally. The Vac-Valve should ONLY open when there is insufficient air flow to the central vacuum unit.

5) The Vac-Valve is equipped with a lock nut which should be set against the adjuster nut. This will ensure that the Vac-Valves tension setting remains constant. The Vac-Valve is designed to be maintenance free and will provide many years of trouble free operation.

The post Air Relief Valve-PA146 appeared first on Aqua-Air Wet/Dry.

• Clean radius design that maintains maximum airflow
• Built to ASTM standards

The post Medium 90 – Female / Male-PA090 appeared first on Aqua-Air Wet/Dry.

• Ideal for two pipe lines joining into one inlet valve
• Built to ASTM standards

The post Tee Short White-PA133 appeared first on Aqua-Air Wet/Dry.

• Provides an extra connection, ideal for confined spaces
• Clean radius design that maintains maximum airflow
• Built to ASTM standards

The post Tee 90 Degree White-PA0087 appeared first on Aqua-Air Wet/Dry.

The post Short 90 – Female / Female-PA089 appeared first on Aqua-Air Wet/Dry.

The post Long Sweep 90- Female / Female-PA091 appeared first on Aqua-Air Wet/Dry.