valve Archives - Aqua-Air Wet/Dry

Solenoid Valve-PA048

aquaairwetdry — Tue, 17 Jan 2023 21:02:01 +0000

A solenoid valve is a device that is used to control the flow of a fluid or gas through a valve or other flow-control component. It typically consists of a solenoid, which is an electrically-controlled coil of wire that generates a magnetic field when energized, and a valve body or opening that is connected to the solenoid. When the solenoid is energized, the magnetic field causes a plunger or other actuator to move, opening or closing the valve. The term “solenoid valve” refers to the specific type of valve that uses a solenoid to control the flow of the fluid or gas.

The post Solenoid Valve-PA048 appeared first on Aqua-Air Wet/Dry.

Valve, 1 1/2” Flapper ABS-PA106

aquaairwetdry — Fri, 13 Jan 2023 19:32:25 +0000

A flapper valve ABS is a device that is used to control the flow of fluid in a plumbing or other fluid-handling system. In this instance when closed it helps create maximuim suction for the vacuum. It consists of a valve body with a movable part, known as a flapper, that opens and closes to regulate the flow of fluid. The term “1 1/2” refers to the size of the valve, which has a diameter of approximately 1 1/2 inches. The term “ABS” refers to the material of the valve, which is made of a type of plastic known as acrylonitrile-butadiene-styrene. ABS is a strong, durable, and lightweight material that is resistant to impact, chemicals, and extreme temperatures.

The post Valve, 1 1/2” Flapper ABS-PA106 appeared first on Aqua-Air Wet/Dry.

Valve Hanger-AW70

aquaairwetdry — Wed, 11 Jan 2023 20:20:01 +0000

Valve hanger to attach PMV120P to AA261R OR AA261.

Part Number:AW70

The post Valve Hanger-AW70 appeared first on Aqua-Air Wet/Dry.

Check Valve-PA208

aquaairwetdry — Wed, 11 Jan 2023 20:18:15 +0000

Replacement check valve for AA261, AA261R.

Part Number:PA208

The post Check Valve-PA208 appeared first on Aqua-Air Wet/Dry.

Hydry Aluminum Valve- 500 PSI-PMV124V5

aquaairwetdry — Wed, 11 Jan 2023 20:14:13 +0000

A durable valve made of high-quality aluminum and designed for long-lasting performance.

Part Number: PMV124V5

The post Hydry Aluminum Valve- 500 PSI-PMV124V5 appeared first on Aqua-Air Wet/Dry.

Air Relief Valve-PA146

aquaairwetdry — Wed, 11 Jan 2023 18:26:32 +0000

*Does not include piping, only includes the Air Relief Valve

VAC-VALVE AIR RELIEF SYSTEM

Purpose: The Vac-Valve is designed to protect your central vacuum system from damage caused by blockage.

The Vac-Valve comes fully assembled and ready for use. However, it is important to install the Vac-Valve properly in order to receive the full protection it was designed to provide.

Installation Instructions:

1) The Vac-Valve should be installed into a sweep 90 tee connection prior to where the pipe enters the central vacuum unit. The valve can sit either horizontally or vertically, as position does not affect its operation. Please ensure the Vac-Valve is mounted securely regardless of its position.

2) The Vac-Valve must be set for the size of the motor in order for it to provide the proper protection. To set the Vac-Valve, tighten the adjuster nut to compress the spring to the point where the valve will not open when the air flow is cut off 100%.

3) Once you reach the point where the Vac-valve will not open, turn the adjuster nut back 1 complete turn (360 degrees). This setting will usually allow the Vac-Valve to open and provide cooling air into the system if a blockage occurs. Sometimes a turn of 360 degrees may not be sufficient to open the Vac-Valve & allow cooling air to enter – so make minor adjustments moving the nut up & down until you reach the point where the Vac-Valve opens when the air flow is cut off 100%.

4) The Vac-Valve should remain closed if the central vacuum is operating normally. The Vac-Valve should ONLY open when there is insufficient air flow to the central vacuum unit.

5) The Vac-Valve is equipped with a lock nut which should be set against the adjuster nut. This will ensure that the Vac-Valves tension setting remains constant. The Vac-Valve is designed to be maintenance free and will provide many years of trouble free operation.

The post Air Relief Valve-PA146 appeared first on Aqua-Air Wet/Dry.

Valve Needle-BR420

aquaairwetdry — Thu, 05 Jan 2023 22:08:50 +0000

A valve needle is a brass fitting that is used to control the flow of a fluid or gas through a valve or other flow-control component. It typically consists of a long, thin, pointed rod or spindle that can be inserted into the valve body or opening, and rotated or moved to open or close the valve. The term “valve needle” refers to the specific type of valve that uses a needle to control the flow of the fluid or gas.

The post Valve Needle-BR420 appeared first on Aqua-Air Wet/Dry.

Inlet Valve Extension White-PA098

aquaairwetdry — Wed, 04 Jan 2023 20:26:07 +0000

Connects Spigot of valve to a mounting plate where wall materials may be thicker than standard. Connections: 2″ Socket x 1 2/3″ Socket

• Accommodates installations on thicker or double drywalls
• Built to ASTM standards

The post Inlet Valve Extension White-PA098 appeared first on Aqua-Air Wet/Dry.